BPC-157 Reconstitution: How Much Bac Water for 5 mg and 10 mg Vials
BPC-157 reconstitution for research: how much bacteriostatic water to add to 5 mg and 10 mg vials, the resulting concentration and U-100 syringe readings, step by step.
Short answer: a 10 mg BPC-157 vial is usually reconstituted with 2 mL of bacteriostatic water (5 mg/mL) or 3 mL (3.33 mg/mL). A 5 mg vial is usually reconstituted with 2 mL (2.5 mg/mL). On a U-100 syringe, 10 units is 0.1 mL, so at 5 mg/mL it holds 0.5 mg.
Research use only. BPC-157 is a research peptide and is not approved for use in people. This page covers laboratory reconstitution and concentration maths only and recommends no amount.
BPC-157 reconstitution chart
| Vial | Bac water | Concentration | 10 units (0.1 mL) | 1 unit |
|---|---|---|---|---|
| 5 mg | 1 mL | 5 mg/mL | 0.5 mg | 50 mcg |
| 5 mg | 2 mL | 2.5 mg/mL | 0.25 mg | 25 mcg |
| 5 mg | 3 mL | 1.67 mg/mL | 0.167 mg | 16.7 mcg |
| 10 mg | 1 mL | 10 mg/mL | 1 mg | 100 mcg |
| 10 mg | 2 mL | 5 mg/mL | 0.5 mg | 50 mcg |
| 10 mg | 3 mL | 3.33 mg/mL | 0.333 mg | 33.3 mcg |
Other numbers: peptide reconstitution calculator.
How to reconstitute BPC-157 (10 mg)
- Check the vial mg and the batch COA.
- Bring the vial and bacteriostatic water to room temperature.
- Swab both stoppers with alcohol and let them dry.
- Draw 2 mL (or your chosen volume) of bacteriostatic water.
- Add it slowly down the inside of the vial, not onto the powder.
- Swirl gently until clear. BPC-157 usually dissolves quickly in water.
- Label the vial: date, 5 mg/mL, water lot.
- Store at 2–8 °C, protected from light.
How much bac water for 10 mg BPC-157?
2 mL is the most common volume because 5 mg/mL makes the maths easy: 1 unit = 50 mcg. With 3 mL each unit holds 33.3 mcg, which suits smaller measurements. With 1 mL each unit holds 100 mcg, and small reading errors become significant.
Signs a reconstituted vial isn’t right
- Cloudiness or floating particles that don’t clear with gentle swirling.
- Foam that remains after a few minutes (often from shaking).
- Colour where the solution should be clear.
If you see any of these, check the COA and the reconstitution steps before using the vial in an experiment. More help: how to reconstitute peptides.
Which water to use
Bacteriostatic water (0.9% benzyl alcohol) is the usual diluent for a vial that will be entered several times. Herbilabs reconstitution solution is a 10 mL bacteriostatic water vial, made in the EU, with a COA for every batch. One vial covers several 2 mL reconstitutions.
FAQ
How much bac water for 5 mg BPC-157?
2 mL gives 2.5 mg/mL; 1 mL gives 5 mg/mL.
Can BPC-157 be reconstituted with sterile water?
Yes, for a single-use vial. For repeated entries, bacteriostatic water is the usual choice.
How long does reconstituted BPC-157 last?
Follow the supplier’s datasheet; keep it at 2–8 °C and avoid freeze–thaw cycles. See how long reconstituted peptides last.
For research and laboratory use only. Not for human or veterinary use. Herbilabs supplies bacteriostatic water only.


